Drying Clay

Clean the surface of runs of old paint and remove all traces of useful steel spatula or loop – a tool used for finishing hardwood floor. Movement in work should be short, "to stripping." After cleaning the surface, wipe with a damp cloth, clean up the cloth and wipe the dust. Allow surface to dry and cover with varnish places are beyond repair. To use natural proolifki varnish or linseed oil "Oksol", adding a 3-5% drier – a liquid, which promotes rapid drying oils. While drying linseed oil (which lasts until this process is 24 hours) Prepare the putty, unless, of course, will not be able to buy it at the store. An example of filler, in grams: Mel 100 250-300 Drying Clay joiner 25-30 (10% solution) in the first warm adhesive is poured varnish, carefully stirring, then add small portions of chalk, and mixed thoroughly. Repaired shpaklyuyut place two or three times so that the surface is smooth, without depressions.

Putty layer dries for about a day, so you can to prepare for painting surfaces. Initially lead to a working state brush. To do this in the middle of the hair is inserted wooden cylinder (you can use natural cork from the bottle). He must take third of the length of the hair brush. Then part the hair until the end of the cork tightly tied up with string.

Prepared in this way the brush dry for 10-15 minutes drive from the brick to align along the length of the bristles and to remove slaboderzhashihsya to brush hair. How to make paint? In gustotertye add white varnish from 1 liter to grow 1 kg of paint and stir, add a little turpentine and drier. Do this for as long as the paint will not run away from Brush a thin stream. Separately, linseed oil (or turpentine) diluted pigment and small amounts are added to white, achieving the desired tone. Keep a ready structure and easy to work with him, having a tank with a tight-fitting cover. After preparing the brush, paint, Primary coated surface (of the primer: 80% and 20% linseed oil paint gustotertoy) and waited until the primer has dried, start painting. Dipping the brush into the jar of paint, wring it out to paint with it is not dripping. Then, on the surface to paint over the top first, then middle and finally, the lower part. Feather each side is horizontal movements, and then vertical. Imposing a first layer, let paint to dry and then apply the second. How to paint wood surfaces? Doors, window sills, casings – paneled brushes and window frames – brushes, towels. Upon completion of works, place the brush in a jar and fill it with water so that water covered the bristle brushes.

Service Manuals

Finally, the letter E – these oil heavyweights with diesel engines or just heavy-duty diesel engines. Now that we understand the recommendations of the plant is necessary to clarify that flooded at the moment. It's time to choose what kind of oil fill: mineral, semi-synthetic or synthetic. Synthetic oil can maintain its performance at high temperature differences (as well as recommended on turbo), and many of the characteristics of oil can not be implemented based on mineral oil. If winter temperatures are not lower than -20, there is no need to use it seriously.

Semi-synthetic oil – this oil consisting of mineral base and synthetic additives. The proportions may change but they are usually from 30 to 50 percent of the mineral foundation. This product is recommended for engines with high mileage because to find exactly what is recommended by the engine manufacturer does not make Labour, in contrast to the mineral. Now, the mixing of oils. If you change the type of oil, naprmier just want to change the oil or butter ugarelo while riding, but not the same with me and nowhere to buy (last resort). Additives of different oils may adversely affect the operation of the engine when mixed.

Most harmless – they just neutralize each other, and the most deplorable – the characteristics of the oil change so much that they would start to wear out faster motor. Of course Oil should always be in the engine, always carry any of this with a small container of oil for topping up, the same make and model as the engine. If it is not at hand and for sale, you should change the oil in the engine completely. As has been said about the additives in the oil they do not like interaction with the additives of other oils. For this reason, the old oil must be drained, pour flush, potarahtet on it for some time (as indicated in the instructions for washing) and then pour the oil is that you see fit. Washing procedure itself is also not safe for the engine, on the frequently changing the brand or type of oil should not be. This compares with the way bleach damages the structure of tissue and subsequently it is broken. According to this take on the oil manufacturer's recommendation engine and the temperature characteristics of your region. And most importantly, at every oil change oil filter change, or new Oil will immediately become dirty due to the remnants of the previous one, used oil in the filter. And remember – oil is not just swill you want to fill, but also washing, lubrication and antikoroziynaya function. Without oil the engine quickly will become worthless, and the repair effort on the wallet. On the timing of oil changes, see the Service Manuals for your car. Some car manufacturers it is kilomterov 5000, some 10, some even 15.

On How To Brew Coffee In Turku

Instant coffee these days is becoming increasingly popular. You bet! Simple, convenient, hassle-free, and, most importantly, fast. Ironically, the real, ground coffee, brewed in a coffee Turk now for the most part is exotic. A person who sprinkles ground coffee in the Turks and somehow managed to boil a priori perceived as a gourmet. Of course, lack of time argument seriously, but think about what you are depriving yourself! None of coffee, even with many tongue-twisting flavors, do not give even a hint of alluring flavor of freshly ground coffee beans, cooked right in Turku for a coffee. And it's not to mention unique, invigorating taste, is able to deliver not only physical (courage), but also moral (ritual) pleasure.

So, forget about the alleged difficulties of preparation, buy a good copper Turk, coffee beans and go to the kitchen to conjure. Speaking of the Turks. Brewing coffee in the unusual vessel is not just a fad or a tradition "Coffeemania", its shape due to the need and has evolved as a result of much trial and error "pioneers" preparing a coffee drink. Maybe coffee Cezve you've never cooked, but this looks like a vessel, for sure, remember. Spout this ridiculous pan narrower than the bottom. This is to ensure that the aromatic substances contained in coffee and to ensure his value is stored in a drink, and eventually he obtained tastier.

Why Turks should be copper? Firstly, for purely practical reasons. Copper Turk is much stronger and more durable than clay or ceramic. And the second – Ideal for conductivity copper material, the liquid is heated evenly, that the most positive effect on the quality of the finished drink. As for cooking, many coffee connoisseurs believe that the boil Coffee – a grievous sin, it needs only a few times (in the classic version – two) to bring to a boil, pour into cups and enjoy!